# @(#)samples/generic/routers	1.3 8/8/92 16:40:26

# This file defines the configuration of the router subsystem as
# compiled into the smail binary.  By modifying the source files
# conf/EDITME, src/config.h or src/default.c the actual internal
# configuration can be changed.  Thus, this should be matched up
# against thes files before assuming this is completely correct.

# force_paths - override file for routing
#
# This entry is not in the compiled-in routers, for now.  However,
# this entry can be very useful for adding temporary override routes,
# if some paths are known to be useless for transient reasons, or for
# organizing internal networks without the use of map files.  It can
# also be used to define UUCP sites that you MX for, if you are using
# DNS with the bind router.  In the MX case, add an entry to the file
# /usr/lib/smail/forcepaths such as:
#
#	.foo.org	foo-uucp-gateway!%s
#
# to cause all E-mail to the foo.org domain to be sent to its uucp
# gateway, rather than being matched by the MX router, which will
# not correctly handle MX to UUCP gatewaying, if you use the bind
# version of the inet_hosts router, below.
#
# The file is defined to be an unsorted ASCII file, so that direct
# editing is possible and reasonable.  The "always" attribute forces
# use of the router even if a later router (such as the bind version
# of inet_hosts) gets a better match (note that DNS wildcard matches
# count as complete hostname matches).  Thus, with the .foo.org
# entry above, foo.foo.org would be matched here, even if foo.foo.org
# were matched by inet_hosts or the regular paths router.
#
#force_paths:
#	driver=pathalias,
#	transport=uux,			# deliver using uux to rmail
#	always;				# force use even if some other
#					# router gets a more complete match
#
#	file=forcepaths,		# plain ASCII file (unsorted)
#	proto=lsearch,			# use linear search
#	optional,			# ignore if the file does not exist

# inet_addrs and inet_hosts are only defined when BSD networking exists

# inet_addrs - match domain literals containing literal IP addresses
#
# For example, [128.103.1.1] will match harvard.harvard.edu on the internet.
# The library routine gethostbyaddr(3N) will be called to see if a reverse
# mapping to the cononical hostname is available.
inet_addrs:
	driver=gethostbyaddr,		# router to match IP domain literals
	transport=smtp;			# deliver using SMTP over TCP/IP

	fail_if_error,			# fail malformed domain literal addrs
	check_for_local,		# see if this is really the local host

# inet_hosts - match hostnames with gethostbyname(3N)
#
# Comment this out if you wish to use the bind version below, instead.
inet_hosts:
	driver=gethostbyname,		# match hosts with the library function
	transport=smtp;			# use default SMTP (may be UUCP-style)

	-required,			# no required domains
	-domain,			# no defined domain suffixes
	-only_local_domain,		# don't restrict to defined domains

# inet_hosts - alternate version using BIND to access the DNS
#
# This router is not compiled-in by default.  It can be used as a
# replacement for the above inet_hosts router, if your system supports
# a bind compatible DNS resolver library.  This should be used for
# systems on the internet.
#inet_hosts:
#	driver=bind,
#	transport=smtp;			# use TCP/IP SMTP for delivery
#
#	defnames,			# use standard domain searching
#	defer_no_connect,		# try again if the nameserver is down
#	-local_mx_okay,			# fail (don't pass through) an MX
#					# to the local host

# paths - route using a paths file, like that produced by the pathalias program
paths:	driver=pathalias,		# general-use paths router
	transport=uux;			# for matches, deliver over UUCP

	file=paths,			# sorted file containing path info
	proto=bsearch,			# use a binary search
#	proto=dbm,			# use a dbm files
	optional,			# ignore if the file does not exist
	-required,			# no required domains
	domain=uucp,			# strip ending ".uucp" before searching

# uucp_neighbors - match neighbors accessible over UUCP
uucp_neighbors:
	driver=uuname,			# use a program which returns neighbors
	transport=uux;

	cmd=/usr/bin/uuname,		# specifically, use the uuname program
	domain=uucp,			# strip ending ".uucp" before searching

# smart_host - a partically specified smarthost director
#
# If the config file attribute smart_path is defined as a path from the
# local host to a remote host, then hostnames not matched otherwise will
# be sent off to the stated remote host.  The config file attribute
# smart_transport can be used to specify a different transport.
#
# If the smart_path attribute is not defined, this router is ignored.
smart_host:
	driver=smarthost,		# special-case driver
	transport=uux;			# by default deliver over UUCP

	-path,				# use smart_path config file variable
#	path=uunet,			# alternate, set path in this file